The microstructure and ablation behavior of carbon fiber/phenolic aerogel composites
-
摘要: 分别以密度为0.15 g/cm3的铺层炭纤维毡和炭纤维穿刺编织体作增强体，采用酚醛树脂浸渍炭纤维，经溶胶-凝胶过程，制备出不同密度和结构的酚醛气凝胶/炭纤维复合材料（PAC）。研究表明，所制复合材料具有轻质（0.27~0.40 g/cm3）和低热导率（0.056~0.068 W·（m·K）-1）特点；炭纤维穿刺编织体复合材料（P-PAC）的弯曲强度是铺层炭纤维毡复合材料（L-PAC）的2倍，当P-PAC密度为0.40 g/cm3时，其弯曲强度可达35.9 MPa；P-PAC具有更优的耐烧蚀性能，在2 000℃、60 s的烧蚀条件下，其质量烧蚀率为0.0043 g/s、线烧蚀率为0.0147 mm/s。酚醛粒子因纳米尺寸效应能够完全分解、蒸发、升华，充分带走表面热，而气凝胶多孔结构也有效的阻止表面热量向内部传递，因而酚醛气凝胶/炭纤维复合材料具有优异的微烧蚀/隔热一体化功能。
-
关键词:
- 热防护材料 /
- 酚醛气凝胶/炭纤维复合材料 /
- 微烧蚀 /
- 隔热
Abstract: Carbon fiber/phenolic aerogel composites (C/PA) were prepared through sol-gel polymerization of a phenolic resin followed by ambient pressure drying using carbon fiber mats as the reinforcements. The composites have low densities (0.27-0.40 g/cm3) and low room-temperature thermal conductivities (0.056-0.068 W·(m·K)-1). The bend strength of the composite prepared from the pierced carbon fiber mat (P-C/PA) is twice that of the laminated carbon fiber mat (L-C/PA). The highest bend strength obtained was 35.9 MPa for the P-C/PA with a density of 0.40 g/cm3. Under ablation at 2000℃ for 60 s, the mass and linear ablation rates of the P-C/PA were 0.0043 g/s and 0.0147 mm/s, respectively. The phenolic nanoparticles in the aerogel were easily decomposed, evaporated and sublimed to remove superficial heat while the porous network of the aerogels effectively prevented heat transfer from the surface to the interior of the composite. C/PA composites are excellent candidates for bifunctional ablation/insulation applications. -
郭艳芝, 沈军, 王珏. 常压干燥法制备炭气凝胶[J]. 新型炭材料, 2001, 16(3):55-57. (Guo Yan-zhi, Shen Jun, Wang Jue. Preparation of carbon aerogels by atmospheric pressure drying[J]. New Carbon Materials, 2001, 16(3):55-57.) Wu Z S, Yang S B, Sun Y, et al. 3D nitrogen-doped graphene aerogel-supported Fe3O4 nanoparticles as efficient electrocatalysts for the oxygen reduction reaction[J]. Journal of the American Chemical Society, 2012, 134(22):9082-9085. 秦国彤, 李文翠. 气凝胶结构控制[J]. 功能材料, 2000, 31(1):26-28. (Qin Guo-tong, Li Wen-cui. Structure control of aerogels[J]. Journal of Functional Materials, 2000, 31(1):26-28.) Zhang X T, Sui Z Y, Xu B, et al. Mechanically strong and highly conductive graphene aerogel and its use as electrodes for electrochemical power sources[J]. Journal of Materials Chemistry, 2011, 21(18):6494-6497. Piao L Y, Li Y D, Chen J L, et al. Methane decomposition to carbon nanotubes and hydrogen on an alumina supported nickel aerogel catalyst[J]. Catalysis Today, 2002, 74(1):145-155. 孙超. 酚醛树脂基有机气凝胶及炭气凝胶的低成本制备及结构控制[D]. 华东理工大学, 2014. (Sun Chao. Low-cost preparation and structure control of phenolic-novolac based organic aerogels and carbon aerogels[D]. East China University of Science and Technology, 2014.) Jia X F, Dai B W, Zhu Z X, et al. Strong and machinable carbon aerogel monoliths with low thermal conductivity prepared via ambient pressure drying[J]. Carbon, 2016, 108:551-560. 师建军, 严蛟, 孔磊, 等. 基于普通酚醛树脂有机气凝胶的高效制备与研究[J]. 高分子学报, 2015, (2):179-186. (Shi Jian-jun, Yan Jiao, Kong Lei, et al. Efficient preparation and study of organic aerogels based on normal phenolic resin[J]. Acta Polymerica Sinica, 2015, (2):179-186.) 张衍, 王井岗, 刘育建, 等. 新型高残碳酚醛树脂的性能研究[J]. 宇航材料工艺, 2003, 33(5):35-39. (ZHANG Yan, WANG Jing-gang, LIU Yu-jian, et al. A study of performance of high char-yield phenolic resin[J]. Aerospace Materials & Technology, 2003, 33(5):35-39.) Wang S J, Jing X L, Wang Y, et al. High char yield of aryl boron-containing phenolic resins:the effect of phenylboronic acid on the thermal stability and carbonization of phenolic resins[J]. Polymer Degradation and Stability, 2014, 99:1-11. 李贺军. 炭/炭复合材料[J]. 新型炭材料, 2001, 16(2):79-80. (LI He-jun. C/C composite materials[J]. New Carbon Materials, 2001, 16(2):79-80.) 高迪. 酚醛树脂浸渍炭纤维三维编织体的成型与烧蚀行为研究[D]. 哈尔滨工业大学, 2011. (GAO Di. Rearch on fabrication and ablation behavior of phenolic impregnated three-dimention carbon fiber braid composites[D]. Harbin Institute of Technology, 2011.) Bahramian A R, Kokabi M, Famili M H N, et al. Ablation and thermal degradation behaviour of a composite based on resol type phenolic resin:process modeling and experimental[J]. Polymer, 2006, 47(10):3661-3673. Cheng H, Xue H, Hong C, et al. Preparation, mechanical, thermal and ablative properties of lightweight needled carbon fibre felt/phenolic resin aerogel composite with a bird's nest structure[J]. Composites Science and Technology, 2017, 140:63-72. Parmenter K E, Shuman K, Milstein F, et al. Compressive response of lightweight ceramic ablators:phenolic impregnated carbon ablator[J]. Journal of Spacecraft and Rockets, 2001, 38(2):231-236. Lachaud J, Cozmuta I, Mansour N N. Multiscale approach to ablation modeling of phenolic impregnated carbon ablators[J]. Journal of Spacecraft and Rockets, 2010, 47(6):910-921. 杨威, 贾献峰, 乔文明, 等. 刚性短切炭纤维预制体和酚醛浸渍碳烧蚀体的制备及性能[J]. 宇航材料工艺, 2016, 46(2):13-18. (YANG Wei, JIA Xian-feng, QIAO Wen-ming, et al. Preparation and properties of rigid carbon fiber preform and resulting phenolic impregnated carbon ablator[J]. Aerospace Materials & Technology, 2016, 46(2):13-18.) 贾献峰, 刘旭华, 乔文明, 等. 酚醛浸渍碳烧蚀体(PICA)的制备、结构及性能[J]. 宇航材料工艺, 2016, 46(1):77-80. (JIA Xian-feng, LIU Xu-hua, QIAO Wen-ming, et al. Preparation and properties of phenolic impregnated carbon ablator[J]. Aerospace Materials & Technology, 2016, 46(1):77-80.) 闫联生, 傅立坤, 刘晓红. 树脂基防热材料烧蚀性能表征的探讨[J]. 固体火箭技术, 2003, 26(2):53-56. (YAN Lian-sheng, FU Li-kun, LIU Xiao-hong. Erosion characterization of resin-matrix ablation materials[J]. Journal of Solid Rocket Technology, 2003, 26(2):53-56.) 韩杰才, 洪长青, 张幸红, 等. 新型轻质热防护复合材料的研究进展[J]. 载人航天, 2015, 21(4):315-321. (HAN Jie-cai, HONG Chang-qing, ZHANG Xin-hong, et al. Progress of novel lightweight thermal protection composites[J]. Manned Spaceflight, 2015, 21(4):315-321.) -
下载:
点击查看大图
图(1)
计量
- 文章访问数: 596
- HTML全文浏览量: 278
- PDF下载量: 502
- 被引次数: 0
